![]() Correcting this should then sort the label printing at the next print. Usually the problem arises when the setting in the tab is not the same as the tab. Again, check that the label size matches your actual labels and is the same as above, and change it if necessary. Easy Uncomplicated change of labels and tags Individual Biggest range of labels and tags in the market with over 50 SKUs Hardware Paper Width: up to 58mm Resolution: 300 dpi Printing Method: Thermal printing Interface: USB Printing Speed: 100mm/s Dimension: 113.8mm (W) x 172mm (D) x 148mm (H), ca.Go to " Advanced Printing Defaults Paper/Output Paper Size".Check that the label size matches your actual labels.EXPERT TECH HELP: Real experts are available 24/7 to help with set-up, connectivity issues, troubleshooting and much more. Go to " Properties General Printing Preferences Paper/Output Paper Size". Buy Seiko Instruments Smart Label Printer 650, USB, PC/Mac, 3.94 inches/second, 300 DPI: Label Printers.Go to and right click the printer in question.The two settings are stored in the following areas: The blank label problem occurs when this size is not correctly set in both places on the Printer Properties in Windows. label size is set to ' 2.00" x 4.00" ' for labels that actually measure ' 2.25" x 1.25" '. Usually the label size that the printer is expecting is set to a size that does not match your actual label size, e.g. This is generally due to the page size settings in the Printer Properties of Windows being incorrectly set. In some cases when a label printer has been set up and labels are printed, you get a blank label between each one, meaning you waste labels. You may also contact Customer Support for additional warranty options.The following article explains how to fix the problem of Stock/Address labels printing a blank label between each one printed. You may use the link below to find a Brother-authorized service center in your area. Your machine has a one-year limited exchange warranty. If the problem persists, your machine may require service. Turn on the machine and press the Feed button. Plug the power cord back to the electrical outlet.ġ2. SLP software provides what you need to create. Easy-to-load design lets you simply drop in new roll for quick use. 300 dpi resolution creates crisp, clear and legible labels. Lower DK roll release lever and close the top cover.ġ1. Seiko SLP650 - Smart Label Printers, Seiko SLP650, Thermal, 2' Print width, 100 mm/s, 300 dpi, USB, Ink/Toner/Ribbon Not Required, Includes Smart Label Software. Thread the end of the DK roll into the slot until you can see the end emerge from under the black roller.ġ0. Ensure the tape of labels is NOT under the right foot of the spool (the foot has to make direct contact with the five switches located on the right side of the compartment), the tab on the right spool slide between the opening of the guide on the right side and the roll is seated firmly in the compartment.ĩ. Use of an incorrect AC adapter may cause risk of overheating or fire. Re-install the DK roll into the compartment. 1 Use only the AC adapter provided with this printer, or an AC adapter that has been approved by Seiko Instruments for use with this printer. ![]() Repeat the above step if necessary to ensure there are no pieces of label jammed inside the machine.Ĩ. With two business cards, insert them into the slot from the DK roll compartment push them toward the front of the machine, forcing any jammed label out and then pull the business cards back out.ħ. ![]() Repeat the above step to ensure no label stuck to the roller.Ħ. With your thumbs rotate the roller 1/3 turns, peel off any visible label.ĥ. Peel off any visible label that is stuck to roller.Ĥ. Open the cover, lift up the DK roll release lever and remove the DK roll from the compartment.ģ. Turn off the machine and unplug the power cord from the electrical outlet.Ģ.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |